標準編號:	QB/T 2002.2-2018
中文名稱:	皮革五金配件 表面噴涂層技術條件
英文名稱:	Hardware fitting of leather products-Specification of sprayed coating
行業分類:	QB    輕工行業標準
發布日期:	2018-04-30
實施日期:	2018-9-1
標準狀態:	valid
替代舊標準:	QB/T 2002.2-1994 皮革五金配件表面噴涂層技術條件
翻譯語言:	英文
文件格式:	PDF
中文字符數:	6000 字
翻譯價格(元):	290.0
交付時間:	付款后 1 個工作日

Codeofchina.com is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative. QB/T 2002 consists of the following two parts under the general title Hardware fitting of leather products: ——Specification of electroplated layer; ——Specification of sprayed coating. This is Part 2 of QB/T 2002. This part is developed in accordance with the rules given in GB/T 1.1-2009. This part is a revision of QB/T 2002.2-1994 Technical conditions of surface spray painting of leather hardware fittings. In addition to a number of editorial changes, the following technical changes have been made with respect to QB/T 2002.2-1994: ——“Terms and definitions” is added;; ——“Appearance quality” requirements are detailed; ——“Hardness” requirements are deleted; ——Test methods for “adhesion” are modified; ——Assessment standard and test cycle for “corrosion resistance” are added; ——"Inspection rules" is modified. This part was proposed by China National Light Industry Council. This part is under the jurisdiction of National Technical Committee on Leather of Standardization Administration of China (SAC/TC 252). This part replaces the former professional standard QB/T 2002.2-1994 Technical conditions of surface spray painting of leather hardware fittings, which is abolished from the implementation date of this part. The previous edition of this part is as follows: ——QB/T 2002.2-1994. Hardware fitting of leather products - Specification of sprayed coating 1 Scope This part of QB/T 2002 specifies terms and definitions, requirements, test methods and inspection rules for sprayed coating of hardware fitting of leather products. It applies to the sprayed coating of various hardware fittings of leather products and may be referenced by other organic coatings. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 1771 Paints and varnishes - Determination of resistance to neutral salt spray (fog) GB/T 13452.2-2008 Paints and varnishes - Determination of film thickness 3 Terms and definitions For the purposes of this part, the following terms and definitions apply. 3.1 sagging traces of spray liquid flowing down on surface of the hardware 3.2 orange peel corrugated surface treatment layer similar to orange peel 4 Classification The sprayed coating is divided into plastic sprayed coating and paint sprayed coating. 5 Appearance quality The exposed sprayed coating shall have the same color and be free from sagging, orange peel, whitening, shrinkage, wrinkle, missed spraying, pile paint, paint peel, obvious blistering, particles and pinholes. 5.2 Adhesion The paint sprayed coating shall be shedding-free. 5.3 Thickness The thickness shall not exceed 100μm. 5.4 Corrosion resistance The number of corrosion spots shall not exceed 3, and the area of a single corrosion spot shall not be greater than 1mm2. 6 Test methods 6.1 Appearance quality Conduct visual inspection in case of good light. 6.2 Adhesion Make 6 passes of about 5mm-long parallel scratches, at an interval of 1mm, on the surface of sprayed coating with a stylus or steel needle with curvature of 0.013mm~0.018mm in the direction perpendicular to the length of sample. The stylus or steel needle shall pass through the entire depth of the sprayed coating. Then make 3 passes of about 8mm-long scratches, at an interval of 1mm, in the direction perpendicular to the previous 6 scratches to form 10 small squares. Gently touch with hands and observe the shedding situation of the sprayed coating.

Foreword i 1 Scope 2 Normative references 3 Terms and definitions 4 Requirements 5 Test methods 6 Inspection rules

ICS 59.140.35 分類號：Y48 備案號：63697-2018 中華人民共和國輕工行業標準 QB/T 2002.2—2018 代替QB/T 2002.2—1994 皮革五金配件 表面噴涂層技術條件 Hardware fitting of leather products—Specification of sprayed coating 2018-05-08發布 2018-09-01實施 中華人民共和國工業和信息化部 發布 前言 QB/T 2002《皮革五金配件》由兩部分組成： ——電鍍層技術條件； ——表面噴涂層技術條件。 本部分為QB/T 2002的第2部分。 本部分按照GB/T 1.1—2009給出的規則起草。 本部分是對QB/T 2002.2—1994《皮革五金配件 表面噴涂層技術條件》的修訂。 本部分與QB/T 2002.2—1994相比，除編輯性修改外主要技術變化如下： ——增加了“術語和定義”； ——細化了“外觀質量”要求； ——?jiǎng)h除了“硬度”要求； ——修改了“附著力”的試驗方法； ——增加了“耐腐蝕性”的評價標準及試驗周期； ——修改了“檢驗規則”。 本部分由中國輕工業聯合會提出。 本部分由全國皮革工業標準化技術委員會(SAC/TC 252)歸口。 本部分自實施之日起，代替原輕工行業標準QB/T 2002.2—1994《皮革五金配件 表面噴涂層技術條件》，原輕工行業標準QB/T 2002.2—1994《皮革五金配件 表面噴涂層技術條件》廢止。 本部分所代替部分的歷次版本發布情況為： ——QB/T 2002.2—1994。 皮革五金配件 表面噴涂層技術條件 1 范圍 QB/T 2002的本部分規定了皮革五金配件表面噴涂層的術語和定義、要求、試驗方法和檢驗規則。 本部分適用于各種皮革五金件表面噴涂層，其他有機覆蓋層可參照使用。 2規范性引用文件 下列文件對本文件的應用是必不可少的，凡是注日期的引用文件，僅注日期的版本適用于本文件。凡是不注日期的引用文件，其最新版本(包括所有的修改單)適用于本文件。 GB/T 1771 色漆和清漆 耐中性鹽霧性能的測定 GB/T 13452.2—2008 色漆和清漆 漆膜厚度的測定 3術語和定義 下列術語和定義適用于本文件。 3.1 流掛 sagging 五金件表面有噴涂液向下流淌的痕跡。 3.2 桔皮orange peel 類似于桔皮波紋狀的表面處理層。 4分類 噴涂層分為噴塑層、噴漆層。 5 外觀質量 外露噴涂層應色澤一致，無流掛、桔皮、泛白、收縮、起皺、漏噴、堆漆、脫漆，無明顯起泡、顆粒及針孔。 5.2附著力 噴漆層應無脫落。 5.3厚度 不應大于100μm。 5.4耐腐蝕性 腐蝕點個數不超過3個，且單個腐蝕點面積不大于1 mm2。 6試驗方法 6.1 外觀質量 在光線良好的情況下目測檢驗。 6.2附著力 用針尖曲率半徑為0.013 mm～0.018 mm的唱針或鋼針，垂直于樣品長度的方向，在噴涂層表面劃6道長度約5 mm的平行劃痕，劃痕間距1 mm，唱針或鋼針應劃穿噴涂層的整個深度，然后再劃與前面6道劃痕垂直的3道劃痕，長度約8 mm，劃痕間距1 mm，形成10個小方格，用手輕輕觸摸，觀察噴涂層的脫落情況。 6.3厚度 按GB/T 13452.2—2008第7章進行檢驗。 6.4耐腐蝕性 按GB/T 1771進行檢驗，不劃痕，試驗時間為16 h。 7檢驗規則 7.1 組批 以同品種原料投產，按同一生產工藝生產出來的同一品種的產品組成一個檢驗批。 7.2出廠檢驗 7.2.1 每批產品出廠前應逐個進行檢驗，經檢驗合格后方可出廠。 7.2.2檢驗項目：外觀質量。 7.3型式檢驗 7.3.1 有下列情況之一時，應進行型式檢驗： a)產品結構、工藝、材料有重大改變時； b)產品停產半年以上恢復生產時； c)國家質量監督機構提出進行型式檢驗時； d)正常生產時，每半年至少進行1次型式檢驗。 7.3.2抽樣數量 從出廠檢驗合格產品中隨機抽取12個進行檢驗，外觀質量、附著力、厚度、耐腐蝕性4個項目各取3個分別進行測試。 7.3.3合格判定 7.3.3.1單項判定規則 每項取3個試樣測試，出現1個或1個以上不合格，則判該項不合格。若產品出現影響產品使用功能的缺陷，即可判該產品不合格。 7.3.3.2批判定規則 外觀質量、附著力、厚度、耐腐蝕性全部合格，則判該批產品合格。若有1項(及以上)不合格，則加倍抽樣進行復驗。復驗全部合格，則判該批產品合格；若有1項(及以上)不合格，則判該批產品不合格。