Codeofchina.com is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative.
GB/T 9160 consists of two parts, under the general title: Rolling bearings—Accessories:
—— Part 1: Adapter sleeve assemblies and withdrawal sleeves;
—— Part 2: Locknuts and locking devices
This is Part 2 of GB/T 9160.
This part is developed in accordance with the rules given in GB/T 1.1-2009.
This part replaces GB/T 9160.2-2006 Rolling bearings—Accessories—Part 2: Locknuts and locking devices. In addition to editorial changes, the following main technical changes have been made with respect to GB/T 9160.2-2006:
—— The expression of identification code is modified (see Chapter 5 of this edition and Chapter 5 of 2006 edition);
——The models of lockwashers applicable to locknuts KM42~KM56 are deleted (see Table 1 of 2006 edition);
——Some reference dimensions for HM and HML series locknuts are added (see Tables 4 and 5);
—— Requirements for material of lockwasher and locking clip are modified (see 8.1 of this edition and 8.1 of 2006 edition);
—— Requirements for surface roughness of lockwasher and locking clip are modified (see Table 13 of this edition and Table 13 of 2006 edition);
—— Structural diagram and boundary dimension table of lockwasher with bent inner tab are moved to the annex (see annex A of this edition, and Figure 3 and Table 5 of 2006 edition).
This part is redrafted by reference to and not equivalent to ISO 2982-1:2013 Rolling bearings—Accessories—Part 2: Dimensions for locknuts and locking devices.
This part was proposed by the China Machinery Industry Federation.
This part is under the jurisdiction of the National Technical Committee on Rolling Bearing of Standardization Administration of China (SAT/TC 98).
The previous standard replaced by this standard is as follows:
——GB/T 9160.2-2006.
Rolling bearings—Accessories—Part 2: Locknuts and locking devices
1 Scope
This part of GB/T 9160 specifies identification code, boundary dimension, technical requirements, test methods, inspection rules and marking and rust-proof packaging of locknuts and locking devices mainly used for adapter sleeves and withdrawal sleeves and threaded shafts produced according to the requirements of GB/T 9160.1.
This part is applicable to production, inspection and acceptance of locknuts and locking devices.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 192 General purpose metric screw threads—Basic profile
GB/T 196 General purpose metric screw threads—Basic dimensions
GB/T 272 Rolling bearings—Identification code
GB/T 699 Quality carbon structure steel
GB/T 708 Dimension, shape, weight and tolerance for cold-rolled steel plates and sheets
GB/T 1800.1 Geometrical product specifications (GPS)—Limits and fits—Part 1: bases of tolerances, deviations and fits
GB/T 2516 General purpose metric screw threads—Limit deviations
GB/T 5796.1 Trapezoidal screw threads—Part 1:Profiles
GB/T 5796.3 Trapezoidal screw threads—Part 3:Basic dimensions
GB/T 5796.4 Trapezoidal screw threads—Part 4:Tolerances
GB/T 6930 Rolling bearings—Vocabulary
GB/T 8597 Rolling bearings—Rust proof packaging
GB/T 9160.1 Rolling bearings—Accessories—Part 1: Adapter sleeve assemblies and withdrawal sleeves
GB/T 24605 Rolling bearings—Marking for products
GB/T 24608 Inspection rules for rolling bearings and commercial parts
3 Terms and definitions
For the purposes of this document, the terms and definitions given in GB/T 6930 and the following apply.
3.1
locking clip
part in C-shape for securing a locknut
3.2
locking clip assembly
assembly comprising a locking clip and a bolt
4 Symbols
For the purposes of this document, the following symbols apply.
The symbols shown in Figures 1 to 4 (excluding tolerance symbols) and the values listed in Tables 2 to 9 denote nominal dimensions, unless specified otherwise.
4.1 Locknuts (see Figures 1 and 2)
B: locknut width
b: width of slot in locknut
d1: outside diameter of clamp face of locknut
d2: outside diameter of locknut
dp: diameter of hole center circle
G, G1, G2: designation of screw thread
h: depth of slot in locknut
lG: depth of hole
Sd: runout tolerance of locknut clamp face (30° chamfered end surface) with respect to pitch diameter of screw thread
Δbs: deviation of width of slot in locknut
ΔBs: deviation of locknut width
Δd1s: deviation of outside diameter of clamp face of locknut
Δd2s: deviation of outside diameter of locknut
Δhs: deviation of depth of slot in locknut
Figure 1 Locknuts with 4 slots
Figure 2 Locknuts with 8 slots
4.2 Lockwasher (see Figure 3)
B7: thickness of lockwasher
d3: bore diameter of lockwasher
d4: root diameter of outer tab of lockwasher
d5: outside diameter of lockwasher
f: width of outer tab of lockwasher
f1: width of inner tab of lockwasher
M: distance between inner tab and bore
N: minimum number of outer tabs of lockwasher
ΔB7s: deviation of material thickness of lockwasher
Δd3s: deviation of bore diameter of lockwasher
Δd4s: deviation of root diameter of outer tab of lockwasher
Δfs: deviation of width of outer tab of lockwasher
Δf1s: deviation of width of inner tab of lockwasher
ΔMs: deviation of distance between inner tab and bore
Figure 3 Lockwasher
4.3 Locking clip assembly (see Figure 4)
b1: width of locking clip
d6: diameter of hole in locking clip
e: inner width of locking clip
G2: designation of screw thread
h1: height of locking clip
l: length of bolt
s: material thickness of locking clip
Δb1s: deviation of width of locking clip
Δes: deviation of inner width of locking clip
a) Bolt
b) Locking clip
Note: The bolts may or may not be secured when supplied.
Figure 4 Locking clip assembly
5 Identification code
5.1 General
Code of locknut, lockwasher and locking clip assembly all consist of type code, dimension series code and diameter code indicating the nominal diameter of the nut, which are arranged as follows:
5.2 Type code
Type codes are denoted by letters, as specified in Table 1.
Table 1 Type code
Type of locking device Type code Meanings
Locknut KM Locknuts with 4 slots (matching with lockwasher in the adapter assembly)
HM Locknuts with 8 slots (matching with locking clip assembly in the adapter assembly)
Lockwasher MB Lockwashers with straight inner tab
MBA Lockwashers with bent inner tab
Locking clip assembly MS Locking clip assembly
5.3 Dimension series code
Dimension series codes are denoted by the letter "L", and the dimension series are used for the adapter sleeves and the withdrawal sleeves of the dimension series 30, 39 and 40 as specified in GB/T 9160.1. Other series codes are omitted.
5.4 Diameter code
The diameter code indicating the nominal diameter of the locknut thread is in accordance with the bearing inner diameter code specified in GB/T 272.
Foreword i
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Identification code
6 Marking example
7 Boundary dimension
8 Technical requirements
9 Test methods
10 Inspection rules
11 Marking
12 Rust-proof packaging
Annex A (Informative) Lockwashers with bent inner tab
