標準編號:	GB/T 4679-2017
中文名稱:	壓鑄模 零件 技術條件
英文名稱:	Diecasting dies--Components--Specifications
中標分類:	J46    模具
行業分類:	GB    國家標準
ICS分類:	25.120.30 25.120.30    模制設備和鑄造設備 25.120.30
發布機構:	中華人民共和國國家質量監督檢驗檢疫總局 中國國家標準化管理委員會
發布日期:	2017-09-29
實施日期:	2018-4-1
標準狀態:	valid
替代舊標準:	GB/T 4679-2003 壓鑄模零件技術條件
翻譯語言:	英文
文件格式:	PDF
中文字符數:	7000 字
翻譯價格(元):	360.0
交付時間:	付款后 1 個工作日

Codeofchina.com is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative. This standard is developed in accordance with the rules given in GB/T 1.1-2009. This standard replaces GB/T 4679-2003 Specification of die-casting die components. The following main editorial and technical changes have been made with respect to GB/T 4679-2003: ——The standard name is changed into three sections, namely Diecasting dies - Components - Specifications; ——Normative modifications are made to the content and structure of the standard according to the requirements of the current national standards; ——Three normative references, namely, GB/T 230.1, GB/T 231.1, and GB/T 825, are added; ——Inspection methods are added (see 4.2, 4.3, and 4.4). This standard was proposed by and is under the jurisdiction of the National Technical Committee 33 on Die and Mould of Standardization Administration of China (SAC/TC 33). The previous editions of this standard are as follows: ——GB/T 4679-1984 and GB/T 4679-2003. Diecasting dies - Components - Specifications 1 Scope This standard specifies the requirements, inspection methods, and marking, packaging and transportation of diecasting die components. This standard is applicable to diecasting die components. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 145 Center holes GB/T 230.1 Metallic materials - Rockwell hardness test - Part 1: Test method (scales A, B, C, D, E, F, G, H, K, N, T) GB/T 231.1 Metallic materials - Brinell hardness test - Part 1: Test method GB/T 825 Eyebolts GB/T 1184-1996 Geometrical tolerancing - Geometrical tolerances for features without individual tolerance indications GB/T 1804-2000 General tolerances - Tolerances for linear and angular dimensions without individual tolerance indications GB/T 4678 (all parts) Die-casting die components GB/T 6403.5 Relief grooves for grinding wheels 3 Requirements 3.1 The limit deviation of the dimensions without individual tolerance indications in the drawings shall meet the requirements of Class m in GB/T 1804-2000, Clause 5. 3.2 The shape and position tolerances not noted in the drawings shall meet the requirements of Class H in GB/T 1184-1996, Clause 5. 3.3 The components shall be free of defects such as rust, bumps and dents. 3.4 The materials selected for die components shall meet the technical standards of corresponding designation. Materials with performance superior to those recommended in GB/T 4678 are allowed. 3.5 The components shall have uniform hardness after heat treatment and be free of cracks, decarburization or oxide spots. 3.6 The relief grooves for grinding wheels with dimension unmarked in the drawings shall meet the requirements of GB/T 6403.5. 3.7 The center holes with dimension unmarked in the drawings shall comply with GB/T 145. 3.8 The side reference plane of the die plate should be marked. 3.9 When the mass of components exceeds 15kg, lifting screw holes shall be set up, and eyebolts shall meet the requirements of GB/T 825. 3.10 All components shall be free of burr. 3.11 The chamfers without marked dimension in the drawings shall be (0.5mm~5mm)×45°. 4 Inspection rules 4.1 The components shall be inspected in accordance with GB/T 4678 and this standard. 4.2 Brinell hardness of components shall be inspected in accordance with GB/T 231.1 and Rockwell hardness in accordance with GB/T 230.1. 4.3 The dimensions of components should be measured with general measuring tools, and the shapes and positions should be measured with coordinate measuring machines. 4.4 The components with surface roughness, Ra, lower than 1.6 μm should be tested by roughness measuring instrument, and the rest shall be test by roughness sample piece comparison method (visual comparison).

Foreword i 1 Scope 2 Normative references 3 Requirements 4 Inspection rules 5 Marking, packaging and transportation

ICS 25.120.30 J 46 中華人民共和國國家標準 GB/T 4679—2017 代替GB/T 4679—2003 壓鑄模 零件 技術條件 Diecasting dies—Components—Specifications 2017—09—29發布 2018—04—01實施 中華人民共和國國家質量監督檢驗檢疫總局 中國國家標準化管理委員會 發布 前言 本標準按照GB/T 1.1—2009給出的規則起草。 本標準代替GB/T 4679—2003《壓鑄模零件技術條件》。 本標準與GB/T 4679—2003相比，主要編輯性和技術性變化如下： ——將標準名稱改為三段式，更名為《壓鑄模 零件 技術條件》； ——按現行國家標準的要求對標準內容和結構進行了規范性修改； ——增加了GB/T 230.1、GB/T 231.1、GB/T 825共3項規范性引用文件； ——增加了檢驗方法，見4.2、4.3、4.4。 本標準由全國模具標準化技術委員會(SAC/TC 33)提出并歸口。 本標準所代替標準的歷次版本發布情況為： ——GB/T 4679—1984、GB/T 4679—2003。 壓鑄模 零件 技術條件 1 范圍 本標準規定了壓鑄模零件的要求、檢驗規則和標志、包裝、運輸。 本標準適用于壓鑄模零件。 2規范性引用文件 下列文件對于本文件的應用是必不可少的。凡是注日期的引用文件，僅注日期的版本適用于本文件。凡是不注日期的引用文件，其最新版本(包括所有的修改單)適用于本文件。 68/T 145 中心孔 GB/T 230.1 金屬材料 洛氏硬度試驗 第1部分：試驗方法(A、B、C、D、E、F、G、H、K、N、T標尺) GB/T 231.1金屬材料 布氏硬度試驗 第1部分：試驗方法 68/T 825吊環螺釘 GB/T 1184—1996形狀和位置公差 未注公差值 68/T 1804—2000 一般公差 未注公差的線性尺寸和角度尺寸的公差 GB/T 4678(所有部分)壓鑄模 零件 GB/T 6403.5砂輪越程槽 3 要求 3.1 圖樣中未注公差尺寸的極限偏差應符合GB/T 1804—2000中第5章m級的規定。 3.2 圖樣中未注的形狀和位置公差應符合GB/T 1184—1996中第5章H級的規定。 3.3 零件表面不準許有銹斑、碰傷和凹痕等缺陷。 3.4模具零件所選用的材料應符合相應牌號的技術標準。允許采用性能高于GB/T 4678中推薦的材料。 3.5零件經熱處理后硬度應均勻，不準許有裂紋、脫碳、氧化斑點。 3.6 圖樣中未注尺寸的砂輪越程槽應符合GB/T 6403.5的規定。 3.7 圖樣中未注尺寸的中心孔應符合GB/T 145的規定。 3.8模板的側向基準面上宜設置標記。 3.9零件質量超過15 kg時，應設起吊螺孔，吊環螺釘應符合GB/T 825的規定。 3.10零件均應去毛刺。 3.11 圖樣中未注尺寸的倒角應為(0.5 mm～5 mm)×45°。 4檢驗規則 4.1 零件應按GB/T 4678和本標準的規定進行檢驗。 4.2零件布氏硬度檢驗應符合GB/T 231.1的規定，洛氏硬度檢驗應符合GB/T 230.1的規定。 4.3零件尺寸宜采用通用量具檢測，形狀和位置尺寸宜采用三坐標測量機檢驗。 4.4 零件表面粗糙度Ra 1.6 μm以下宜采用粗糙度測量?jī)x檢驗，其余表面粗糙度宜采用粗糙度樣塊目測比較法檢驗。 5標志、包裝、運輸 5.1 檢驗合格的零件應做合格標記或附有合格標簽。 5.2零件在入庫前應擦拭干凈，并做表面防銹處理。 5.3零件包裝應防潮、防磕碰，保證在運輸中完好無損。