標準編號:	GB/T 16507.8-2022
中文名稱:	水管鍋爐 第8部分：安裝與運行
英文名稱:	Water-tube boilers—Part 8: Installation and operation
行業分類:	GB    國家標準
ICS分類:	27.060.30 27.060.30    鍋爐和熱交換器 27.060.30
發布機構:	國家市場監督管理總局 國家標準化管理委員會
發布日期:	2022-03-09
實施日期:	2022-10-1
標準狀態:	valid
替代舊標準:	GB/T 16507.8-2013 水管鍋爐 第8部分：安裝與運行
翻譯語言:	英文
文件格式:	PDF
中文字符數:	39000 字
翻譯價格(元):	2560.0
交付時間:	付款后 1 個工作日

Water-tube boilers - Part 8: Installation and operation English 1 Scope This document specifies the requirements for installation, commissioning, quality acceptance and operation of water-tube boiler proper and pipes within the boiler range. This document is applicable to the water-tube boilers as defined in GB/T 16507.1. Reference may be made to this document for the modification and repair of water tube boilers. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 1576 Water quality for industrial boilers GB/T 2900.48 Electrotechnical terminology of boilers GB/T 12145 Quality criterion of water and steam for power plant and steam-generating equipment GB/T 16507.1 Water-tube boilers - Part 1: General requirement GB/T 16507.4 Water-tube boilers - Part 4: Strength calculation of pressure parts GB/T 16507.6 Water-tube boilers - Part 6: Inspection, testing and acceptance GB/T 16507.7 Water-tube boilers - Part 7: Safety appurtenances and instruments GB 50016 Code for fire protection design of buildings GB 50041 Standard for design of boiler plant GB 50204 Code for acceptance of constructional quality of concrete structures GB 50205 Code for acceptance of construction quality of steel structures GB 50273 Code for construction and acceptance of boiler installation engineering GB 50275 Code for construction and acceptance of fan, compressor and pump installation DL/T 777 Boiler refractory of thermal power plants DL/T 852 Guide for boiler start-up commissioning test DL/T 902 Abrasion resistant refractory material NB/T 47013 (all parts) Nondestructive testing of pressure equipments 3 Terms and definitions For the purposes of this document, the terms and definitions specified in GB/T 2900.48 and GB/T 16507.1 and the following apply. 3.1 commissioning adjustment, setting and a series of tests specified in the design and equipment technical documents to which the boilers, related equipment and systems are subjected after installation Note: Commissioning is short for adjustment and test. 3.2 commissioning of individual equipment and system dynamic inspection and testing on a single device or system 3.3 start up and commissioning start up and commissioning of whole set of turbine and boiler equipment combined with electrical and thermal automation jointly participated by commissioning, production and construction units on the basis of completing the commissioning of individual equipment and system 4 Basic requirements 4.1 Boiler installation position and buildings shall meet the relevant provisions of GB 50016 and GB 50041 and the requirements of the design drawings. A safe distance shall be kept between the installation position of pipes within the boiler range and the crowded places (such as control room and duty room). When the requirement of safe distance cannot be met, necessary explosion-proof and isolation measures shall be taken for the buildings.

Foreword i Introduction vi 1 Scope 2 Normative references 3 Terms and definitions 4 Basic requirements 5 Foundation, support (frame) and steel structure 6 Boiler drum, start-up (steam-water) separator, water storage tank and header, and desuperheater 7 Heating surface 8 Air pre-heater 9 Boiler proper pipe and pipes within the boiler range 10 Safety appurtenances and instruments 11 Burning device 12 Ancillary devices 13 Platforms, escalators and railings 14 Hydrostatic test 15 Masonry, pouring and thermal insulation of furnace walls 16 Chemical cleaning, rinsing and purging 17 Commissioning 18 Quality acceptance 19 Operation Annex A (Informative) Permissible deviations for grate installation of grate firing boiler Bibliography

水管鍋爐 第8部分：安裝與運行 1 范圍 本文件規定了水管鍋爐本體和鍋爐范圍內管道的安裝、調試、質量驗收以及運行等要求。 本文件適用于GB／T 16507.1界定的水管鍋爐。水管鍋爐的改造、修理可參照使用。 2 規范性引用文件 下列文件中的內容通過文中的規范性引用而構成本文件必不可少的條款。其中，注日期的引用文件，僅該日期對應的版本適用于本文件；不注日期的引用文件，其最新版本(包括所有的修改單)適用于本文件。 GB／T 1576 工業鍋爐水質 GB／T 2900.48 電工名詞術語 鍋爐 GB／T 12145 火力發電機組及蒸汽動力設備水汽質量 GB／T 16507.1 水管鍋爐 第1部分：總則 GB／T 16507.4 水管鍋爐 第4部分：受壓元件強度計算 GB／T 16507.6 水管鍋爐 第6部分：檢驗、試驗和驗收 GB／T 16507.7 水管鍋爐 第7部分：安全附件和儀表 GB 50016 建筑設計防火規范 GB 50041 鍋爐房設計標準 GB 50204 混凝土結構工程施工質量驗收規范 GB 50205 鋼結構工程施工質量驗收標準 GB 50273 鍋爐安裝工程施工及驗收規范 GB 50275 風機、壓縮機、泵安裝工程施工及驗收規范 DL／T 777 火力發電廠鍋爐耐火材料 DL／T 852 鍋爐啟動調試導則 DL／T 902 耐磨耐火材料 NB／T 47013(所有部分) 承壓設備無損檢測 3 術語和定義 GB／T 2900.48和GB／T 16507.1界定的以及下列術語和定義適用于本文件。 3.1 調試 commissioning 鍋爐和相關設備、系統在安裝后按照設計和設備技術文件規定進行調整、整定和一系列試驗工作的總稱。 注：調試是調整和試驗的簡稱。 3.2 分部試運 commissioning of individual equipment and system 對單臺設備或系統進行的動態檢查和試驗。 3.3 整套啟動試運 start up and commissioning 在完成分部試運的基礎上，由調試、生產、施工單位共同參加進行汽機、鍋爐整套設備聯合電氣、熱工自動化的啟動試運。 4 基本要求 4.1 安裝鍋爐的位置和建筑物應滿足GB 50016、GB 50041的有關規定并符合設計圖樣的要求。鍋爐范圍內管道的安裝位置應與人員密集場所(如控制室、值班室等)保持足夠的安全距離。在無法滿足安全距離的要求時，建筑物應采取必要的防爆與隔離措施。 4.2 鍋爐安裝應在土建基礎工作完成并驗收合格后進行。 4.3 鍋爐各部件安裝前應取得鍋爐制造單位的設備制造相關技術文件和質量證明文件，安裝所用的材料進入現場，按照有關規定進行入廠驗收，合格后才能使用。對于合金鋼材料制成的承壓部件的成品、半成品和原材料應進行100％的化學成分光譜分析復驗。 4.4 鍋爐的安裝應符合安全技術規范和制造單位提供的安裝說明書的要求。 4.5 鍋爐安裝焊接施工現場應有防風、防雨雪、防潮和防寒措施。當環境溫度低于0℃或其他惡劣天氣時，應有相應的技術措施。 4.6 鍋爐安裝焊接施工除設計規定的冷拉焊接接頭以外，焊件裝配時不應強力對正，安裝冷拉焊接接頭使用的冷拉工具在焊接、熱處理完畢，并經檢驗合格后方可拆除。 4.7 安置在多層或高層建筑物內的鍋爐，燃料供應管路應采用無縫鋼管，焊接時應采用氬弧焊封底；以氣體為燃料的燃料管路應有燃?xì)鈾z漏報警裝置。 4.8 鍋爐施工單位應對安裝質量進行自檢，并形成自檢記錄和報告。隱蔽工程在隱蔽前應經檢查驗收合格。 4.9 鍋爐在安裝施工和其質量檢驗、檢測中使用的設備、工具、量具、儀器儀表等應處在良好的使用狀態，符合規定的精度要求，并定期進行檢查和校驗。 4.10 鍋爐設備吊裝前，應對設備的臨時加固設施和吊裝設施進行全面宏觀檢查，必要時進行無損檢測，合格后才可以進行吊裝。 4.11 安裝施工前，應對制造單位提供的成品和半成品進行產品質量證明文件和外觀檢查，核對關鍵結構是否符合圖樣要求，必要時對主要安裝尺寸進行測量與復核校對。 4.12 安裝施工過程中應做好成品保護措施，施工結束后應解除保護措施，消除施工用臨時設施的痕跡。