Codeofchina.com is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative.
1 Subject content
This standard specifies the hexagon bolts with slot on head with the thread specification of M3 to M12.
The bolt is made to straight grooves in the head according to GB 5783.
2 Normative references
GB 5783 Hexagon head bolts - Full thread - Product A and B
GB 1237 Designation system for fasteners
3 Dimensions
The dimensions are shown in the following figure and Table 1.
Other types and dimensions shall meet the requirements of GB 5783.
Table 1 mm
Thread specification d M3 M4 M5 M6 M8 M10 M12
n Nom. 0.8 1.2 1.2 1.6 2 2.5 3
min 0.86 1.26 1.28 1.66 2.06 2.56 3.06
max 1 1.51 1.51 1.91 2.31 2.81 3.31
t min 0.7 1 1.2 1.4 1.9 2.4 3
4 Technical conditions
The technical conditions shall meet the requirements of GB 5783.
5 Designation
5.1 The designation method shall meet the requirements of GB 1237.
?
5.2 Example of designation:
The hexagon bolt with slot on head with the thread specification d = M12, nominal length l = 80 mm, property class of 8.8, subjected to surface oxidation, with full thread and Product A is designated as:
Bolt GB 29.1 M12 × 80
中華人民共和國國家標準
UDC 621.882.6
GB 29.1—88
代替GB 29—76
六角頭頭部帶槽螺栓 A和B級
Hexagon bolts with slot on head—Product
A and B
國家機械工業委員會1988-06-24批準 1989-07-01實施
1 主題內容
本標準規定了螺紋規格為M3～M12的六角頭頭部帶槽螺栓。
該螺栓是在GB 5783的頭部制出一字槽。
2 引用標準
GB 5783 六角頭螺栓—全螺紋—A和B級
GB 1237 緊固件的標記方法
3 尺寸
尺寸如下圖及表1所示。
其余的型式與尺寸按GB 5783規定。
表1 mm
螺紋規格d M3 M4 M5 M6 M8 M10 M12
n 公稱 0.8 1.2 1.2 1.6 2 2.5 3
min 0.86 1.26 1.28 1.66 2.06 2.56 3.06
max 1 1.51 1.51 1.91 2.31 2.81 3.31
t min 0.7 1 1.2 1.4 1.9 2.4 3
4 技術條件
技術條件按GB 5783規定。
5 標記
5.1 標記方法按GB 1237規定。
5.2 標記示例：
螺紋規格d＝Ml2、公稱長度l＝80mm、性能等級為8.8級、表面氧化、全螺紋、A級的六角頭頭部帶槽螺栓的標記：
螺栓GB 29.1 M12×80
附加說明：
本標準由全國緊固件標準化技術委員會提出。
本標準由國家機械工業委員會標準化研究所歸口。
