標準編號:	GB 3836.15-2000
中文名稱:	爆炸性氣體環境用電氣設備 第15部分：危險場所電氣安裝（煤礦除外）
英文名稱:	Electrical apparatus for explosive gas atmospheres--Part 15:Electrical installations in hazardous areas(other than mines)
中標分類:	K35    防爆電器
行業分類:	GB    國家標準
ICS分類:	29.260.20 29.260.20    易爆環境用電氣設備 29.260.20
發布機構:	國家質量監督檢驗檢疫總局
發布日期:	2000-10-17
實施日期:	2001-6-1
標準狀態:	superseded
被新標準替代:	GB/T 3836.15-2017 爆炸性環境 第15部分：電氣裝置的設計、選型和安裝
被替代日期:	2018-7-1
作廢日期:	2018-07-01
翻譯語言:	英文
文件格式:	PDF
中文字符數:	30000 字
翻譯價格(元):	900.0
交付時間:	付款后 1 個工作日

1. Scope This Standard defines the specific requirements for the design, selection and mounting of electrical installations in explosive gas atmospheres. These requirements are complementary to the requirements for electrical installations in non-hazardous areas. This Standard applies to all electrical equipment and installations in hazardous areas whether permanent, temporary, movable, transportable or hand-held. This Standard does not apply to: — electrical installations under the shaft of mines; Note： This standard may apply to electrical installations under the shaft of mines with other explosive gas other than firedamp and electrical installations on the ground of mines. — electrical installations in areas where the hazard is due to combustible dusts or fibres; — inherently explosive situations, for example explosive manufacturing and processing; — room used for medical purpose.

Contents Preface…………………………………………………………………………………… IEC Preface……………………………………………………………………………… IEC Introduction………………………………………………………………………… 1. Scope ………………………………………………………………………………… 2． Cited Standards……………………………………………………………………… 3． Definition……………………………………………………………………………… 4. General Rules………………………………………………………………………… 4.1 General Requirements………………………………………………………………… 4.2 Documents…………………………………………………………………………… 5. Selection of electrical apparatus (including cable and conduit)……………………… 5.1 Specific documents…………………………………………………………………… 5.2 Selection according to area classification…………………………………………… 5.3 Selection according to ignition temperature of gas or vapor………………………… 5.4 Selection According To The Category Of Electrical Apparatus…………………… 5.5 External Influences…………………………………………………………………… 6. Prevention of hazardous spark…………………………………………………… 6.1 hazard arising from active parts…………………………………………………… 6.2 Hazard Arising From Bare External Conductor Components……………………… 6.3 Isopotential connection…………………………………………………………… 6.4 Static electricity…………………………………………………………………… 6.5 Lightning-proof…………………………………………………………………… 6.6 Electromagnetic radiation………………………………………………………… 6.7 Cathode protective metal parts…………………………………………………… 7. Electrical protection……………………………………………………………… 8. Emergency switch-off and electrical isolation………………………………… 8.1 Emergency switch-off…………………………………………………………… 8.2 Electrical isolation………………………………………………………………… 9. Wiring system…………………………………………………………………… 9.1 General…………………………………………………………………………… 9.2 Cable system in Zone 0…………………………………………………………… 9.3 Cable system in Zone 1&2………………………………………………………… 9.4 Conduit system…………………………………………………………………… 10. Additional requirements for explosion-proof enclosure“d”…………………… 10.1 Solid barrier ……………………………………………………………………… 10.2 Protection Of Explosion-Proof Surface…………………………………………… 10.3 Cable introducing system………………………………………………………… 10.4 Motor Powered By Frequency Conversion And Voltage Adjustment Power Supply… 10.5 Conduit system…………………………………………………………………… 11. Complementary requirements for safety-increasing “e” explosion-proof type… 11.1 Protective class of enclosure……………………………………………………… 11.2 Squirrel-cage induction motor—thermal protection during operation…………… 11.3 Wiring system…………………………………………………………………… 11.4 Resistance heater………………………………………………………………… 12. Additional requirements for intrinsic-safety “i” ……………………………… 12.1 Introduction……………………………………………………………………… 12.2. Installation in Zone 1 and Zone 2………………………………………………… 12.3 Installation in Zone 0……………………………………………………………… 13. Complementary requirements for electrical apparatus of positive-pressure type “p” ……………………………………………………………………… 13.1 Piping…………………………………………………………………………… 13.2 Measures To Be Taken For Positive-Pressure Failure…………………………… 13.3 Multiple positive-pressure enclosures sharing one safety device……………… 13.4 Purge…………………………………………………………………………… 14. Complementary requirements for equipment used in Zone 2……………… 14.1 Protective class of enclosure…………………………………………………… 14.2 Energy limiting device and circuit……………………………………………… 14.3 Wiring system…………………………………………………………………… 14.4 Motor powered by frequency conversion and voltage adjustment power supply… Appendix A (Appendix for this Standard) Inspection of intrinsic-safety circuit for associated apparatus characterized by more than one linear current/voltage……… Appendix B (appendix for the prompt) Measurement methods of maximum current and maximum voltage for intrinsic-safety circuit system of associated apparatus characterized by more than one linear current/voltage………………………………