標準編號:	GB/T 9109.5-2009
中文名稱:	石油和液體石油產品油量計算 動態計量
英文名稱:	Petroleum and liquid petroleum products - Calculation of oil quantities - Dynamic measurement
中標分類:	E08    標志、包裝、運輸、貯存
行業分類:	GB    國家標準
ICS分類:	75.180.30 75.180.30    容積測量和容積設備 75.180.30
發布機構:	國家標準化管理委員會
發布日期:	2009-3-16
實施日期:	2009-10-1
標準狀態:	superseded
被新標準替代:	GB/T 9109.5-2017 石油和液體石油產品動態計量 第5部分：油量計算
被替代日期:	2017-12-1
作廢日期:	2017-12-01
替代舊標準:	GB/T 9109.5-1988 原油動態計量 油量計量
翻譯語言:	英文
文件格式:	PDF
中文字符數:	22000 字
翻譯價格(元):	1540.0
交付時間:	付款后 1 個工作日

1 Scope This standard specifies calculation method of oil quantities for dynamic measurement of petroleum and liquid petroleum products (hereinafter referred to as petroleum products) and calculation formulas of oil quantities for weight of petroleum products equipped with different measurement tools in the air or volume under standard reference conditions, defines and explains terms and symbols used in calculation of oil quantities for dynamic measurement of petroleum products and gives relevant measurement parameter and converting facter as well as corresponding formulas and numerical tables involved with calculation of oil quantities. This standard is only applicable to dynamic measurement of single-phase petroleum products. Calculation method of dynamic oil quantities specified in this standard exlcudes calculation of oil quantities for liquefied petroleum gas and stable light hydrocarbon Standard reference conditions adopted for calculation of oil quantities in this standard are 20℃ and 101.325kPa. 2 Normative References The following normative documents contain provisions which, through reference in this standard, constitute provisions of this standard.For dated reference, subsequent amendments to (excluding corrigenda), or revisions of, any of these publications do not apply. However, all parties coming to an agreement according to this standard are encouraged to study whether the latest edition of these documents is applicable. For undated references, the latest edition of the normative document is applicable to this national standard.

Contents Foreword I Introduction III 1 Scope 2 Normative References 3 Terms, Definitions and Symbols 4 Significant digits and Value Rounding of Measurement Parameters 5 Preparation of Basic Data 6 Calculation Method of Oil Quantities 7 Measurement document 8 Example for Calculation of Oil Quantities Appendix A (Informative) Reading Rule of Measurement Data Appendix B (Normative) Calculation Method for Correction Factor for Volume Pressure of Petroleum Products Appendix C (Normative) Compressibility Factor for Hydrocarbon Appendix D (Normative) Density Converting for Petroleum and Liquid Petrolatum Products from 20℃ to 15℃ Appendix E (Informative) Mass Converting Factor Appendix F (Informative) Format and Contents of Measurement Document Appendix G (Normative) Converting from Density at 15℃ to Barrel/t Factor