標準編號:	GB/T 43896-2024
中文名稱:	金屬材料 超高周疲勞 超聲疲勞試驗方法
英文名稱:	Metallic materials—Very high cycle fatigue—Ultrasonic fatigue test method
中標分類:	H22    金屬力學性能試驗方法
行業分類:	GB    國家標準
ICS分類:	77.040.10 77.040.10    金屬材料力學試驗 77.040.10
發布機構:	國家市場監督管理總局 國家標準化管理委員會
發布日期:	2024-4-25
實施日期:	2024-11-1
標準狀態:	valid
翻譯語言:	英文
文件格式:	PDF
中文字符數:	29000 字
翻譯價格(元):	2030.0
交付時間:	付款后 1~5 個工作日

Metallic materials - Very high cycle fatigue - Ultrasonic fatigue test method 1 Scope This document specifies the specimen, test apparatus, test procedures and test report of ultrasonic fatigue test method for ultra-high cycle fatigue of metallic materials at room temperature. This document is applicable to ultra-high cycle fatigue test with a test frequency of 20,000 Hz ± 500 Hz, a single-end axial excited vibration and a stress ratio R=-1. Fatigue tests of other stress ratios or ultrasonic resonance frequencies may refer to this method, and the corresponding specimens should be designed and verified separately. Notched specimens are not included in this document, but the fatigue test procedures specified in this document may be applied to the very high cycle fatigue test of notched specimens. 2 Normative references The following documents contain requirements which, through reference in this text, constitute provisions of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 2614 Nickel-Chromium/Nickel-Silicon thermocouple wires GB/T 3075 Metallic materials - Fatigue testing - Axial force-controlled method GB/T 38897 Non-destructive testing - Measurement method for material elastic modulus and Poisson's ratio using ultrasonic velocity JJF 1305 Calibration specification for linear displacement sensors JJG 623 Resistance strain gauge indicators JJG 856 Radiation thermometer for work 3 Terms and definitions For the purposes of this document, the terms and definitions given in GB/T 3075 and the following apply. 3.1 very high cycle fatigue fatigue with cycles greater than 107 3.2 ultrasonic fatigue test fatigue test with cyclic stress applied at ultrasonic resonance frequency 3.3 ultrasonic fatigue specimen fatigue specimens that meet ultrasonic frequency resonance requirements 4 Symbols and designations See Table 1 for symbols used in this document and their corresponding interpretations.

Contents Foreword III Introduction IV 1 Scope 2 Normative references 3 Terms and definitions 4 Symbols and designations 5 Principle 6 Specimen 7 Test apparatus 8 Test procedures 9 Test report Annex A (Informative) Design of ultrasonic fatigue specimen Annex B (Informative) Stress control method of ultrasonic fatigue specimens with different shapes Reference

金屬材料 超高周疲勞 超聲疲勞試驗方法 1 范圍 本文件規定了室溫下金屬材料超高周疲勞超聲疲勞試驗方法的試樣、試驗裝置,試驗步驟及試驗報告。 本文件適用于試驗頻率在20000Hz±500Hz、單端軸向受激振動、應力比R=-1的超高周疲勞試驗。 其他應力比或超聲諧振頻率的疲勞試驗可參照本方法,相應的試樣需要單獨設計與驗證。 本文件不包含缺口試樣,但本文件中描述的疲勞試驗過程可應用于缺口試樣的超高周疲勞試驗。 2 規范性引用文件 下列文件中的內容通過文中的規范性引用面構成本文件必不可少的條款。其中,注目期的引用文件,僅該日期對應的版本適用于本文件;不注日期的引用文件,其最新版本(包括所有的修改單)適用于本文件。 GB/T 2614 鉻-鎳硅熱電偶絲 GB/T 3075 金屬材料疲勞試驗軸向力控制方法 GB/T 38897 無損檢測性模量和泊松比的超聲測量方法 JJF 1305 線位移傳感器校準規范 JG 623 電阻應變儀 JG 856 工作用輻射溫度計 3 術語和定義 GB/T 3075界定的以及下列術語和定義適用于本文件。 3.1 超高周疲勞 very high cycle fatigue 循環周次大于107的疲勞。 3.2 超聲疲勞試驗ultrasonic fatigue test 在超聲諧振頻率下施加循環應力的疲勞試驗。 3.3 超聲疲勞試樣ultrasonic fatigue specimen 滿足超聲頻率諧振要求的疲勞試樣。 4 符號和說明 本文件使用的符號和相應的說明見表1。