標準編號:	GB/T 43005-2023
中文名稱:	給水用連續玻纖帶纏繞增強聚乙烯復合管
英文名稱:	Composite pipes of polyethylene reinforced with continuous wound glass-fiber-tape for water supply
中標分類:	G33    塑料型材
行業分類:	GB    國家標準
ICS分類:	83.140.30 83.140.30    塑料管、配件和閥門 83.140.30
發布機構:	國家市場監督管理總局 國家標準化管理委員會
發布日期:	2023-09-07
實施日期:	2024-4-1
標準狀態:	valid
翻譯語言:	英文
文件格式:	PDF
中文字符數:	17000 字
翻譯價格(元):	1190.0
交付時間:	付款后 1 個工作日

GB/T 43005-2023 Composite pipes of polyethylene reinforced with continuous wound glass-fiber-tape for water supply 1 Scope This document specifies the materials, pressure reduction factor, structure and connection mode, requirements, test methods, inspection rules, marking, packaging, transportation and storage of composite pipes of polyethylene reinforced with continuous wound glass-fiber-tape for water supply (hereinafter referred to as "composite pipes"). This document is applicable to the composite pipes, with water temperature not higher than 40°C, for general purpose pressure water transmission and drinking water transmission and distribution. Considering the influence factors such as chemical resistance and temperature resistance of the materials, it is also applicable to the composite pipes for sewage transportation, seawater transportation and brine transportation in the salt chemical industry. Note: It is the responsibility of the purchaser to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and standards or codes. 2 Normative references The following documents contain requirements which, through reference in this text, constitute provisions of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 1040.5 Plastics - Determination of tensile properties - Part 5: Test conditions for unidirectional fibre-reinforced plastic composites GB/T 2828.1 Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection GB/T 2918 Plastics - Standard atmospheres for conditioning and testing GB/T 3682.1 Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1:Standard method GB/T 6111 Thermoplastics piping systems for the conveyance of fluids - Determination of the resistance to internal pressure GB/T 6671 Thermoplastics pipes - Determination of longitudinal reversion GB/T 6672 Plastics film and sheeting - Determination of thickness by mechanical scanning GB/T 6673 Determination of length and width of plastics film and sheeting GB/T 8806 Plastics piping systems - Plastics components - Determination of dimensions GB/T 9345.1 Plastics - Determination of ash - Part 1: General methods GB/T 9647 Thermoplastics pipes - Determination of ring stiffness GB/T 13021 Determination for the carbon black content of polyethylene pipes and fittings by calcination and pyrolysis GB/T 13663.1 Polyethylene (PE) piping systems for water supply - Part 1: General GB/T 15560 Standard test method for short-time hydraulic failure and resistance to constant internal pressure of the plastics pipes for the transport of fluids GB/T 17219 Standard for safety evaluation of equipment and protective materials in drinking water system GB/T 18251 Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds GB/T 19278 General terms and their definitions of thermoplastic pipes, fittings and valves GB/T 19466.6 Plastics - Differential scanning calorimetry (DSC) - Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) 3 Terms and definitions For the purposes of this document, the terms and definitions given in GB/T 19278 and the following apply. 3.1 composite pipes of polyethylene reinforced with continuous wound glass-fiber-tape reinforced thermoplastic composite pipes are formed by the continuous wound glass-fiber-tape alternately coiled and fused into the reinforcement windings, and the liner and cover of PE are extruded, and the liner and cover are fused into the reinforcement windings in the continuous extrusion process 3.2 liner polymer layer formed by continuous extrusion and in direct contact with the conveying medium 3.3 reinforcement windings main bearing structure that provides the mechanical strength of the composite pipe to meet the load requirements during operation and installation 3.4 cover polymer layer formed by continuous extrusion and on the outside of the composite pipe

Foreword II 1 Scope 2 Normative references 3 Terms and definitions 4 Materials 5 Pressure reduction coefficient 6 Structure and connection mode 7 Requirements 8 Test method 9 Inspection rules 10 Marking, packaging, transportation and storage Annex A (Normative) Fusion strength test of glass-fiber-tape