標準編號:	GB/T 19230.3-2003
中文名稱:	評價汽油清凈劑使用效果的試驗方法 第3部分: 汽油清凈劑對電子孔式燃油噴嘴(PFI)堵塞傾向影響的試驗方法
英文名稱:	Test method for evaluating gasoline detergent in use Part 3: Test method for evaluating gasoline detergent produced effect for electronic port fuel injector(PFI) fouling
中標分類:	E49    其他石油產品
行業分類:	GB    國家標準
ICS分類:	75.140 75.140    石蠟、瀝青材料和其他石油產品: 75.140
發布機構:	中國石油化工集團公司
發布日期:	2003-07-01
實施日期:	2003-1-2
標準狀態:	valid
翻譯語言:	英文
文件格式:	PDF
中文字符數:	12000 字
翻譯價格(元):	720.0
交付時間:	付款后 1 個工作日

1 Scope This part specifies the test method for evaluating gasoline detergent produced effect for electronic port fuel injector (PFI) fouling. This part is applicable to the evaluation of gasoline detergent, vehicle gasoline and its component oil on the detergency of electronic port fuel injector (PFI). Note: This test method is only applicable to evaluate the deposit control performance of gasoline detergent in the top area of the electronic port fuel injector. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part. For dated references, subsequent amendments to (excluding correction to), or revisions of, any of these publications do not apply. However, parties to agreements based on this part are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. For undated references, the latest edition of the normative document applies. GB/T 380 Determination of sulfur content in petroleum products (lamp method) GB/T 503 Determination of the gasoline octane number—Test method for motor octane number GB/T 5487 Determination of the gasoline octane number—Test method for research octane number GB/T 6536 Standard test method for distillation of petroleum products at atmospheric pressure GB/T 8017 Standard test method for vapor pressure of petroleum products—Reid method GB/T 8018 Determination of oxidation stability of gasoline—Induction period method GB/T 8019 Standard test method for gum content in fuels by jet evaporation ? GB/T 11132 Standard test method for hydrocarbon types in liquid petroleum products by fluorescent indicator adsorption SH/T 0174 Qualitative test method for thiols of aromatic hydrocarbons and light petroleum products—Doctor test SH/T 0663 Standard test method for determination of certain alcohols and ethers in gasoline by gas chromatography SH/T 0693 Standard test method for determination of benzene, toluene, ethylbenzene, p/m-xylene, o-xylene, C9 and heavier aromatics, and total aromatics in finished gasoline by gas chromatography ASTM D6421 Standard test method for evaluating automotive spark-ignition engine fuel for electronic port fuel injector fouling by bench procedure 3 Terms and definitions For the purposes of this part, the following term and definition apply. 3.1 cycle 15s pulsing period, followed by a 50 min heating period at 160°C, followed by a 10 min cool-down period 3.2 electronic port fuel injector (PFI) injection device used to control fuel flow into the combustion chamber 3.3 fouling formation of carbonaceous deposits on the pintle or metering surfaces of an electronic port fuel injector, which reduces fuel flow 3.4 pintle needle-like metering device extending beyond the electronic port fuel injector body that is part of an electronic port, which controls flow rate and spray pattern

Foreword i 1 Scope 2 Normative references 3 Terms and definitions 4 Summary of test method 5 Test apparatus and equipment 6 Reagents and materials 7 Test preparation 8 Test procedures 9 Calculation 10 Report 11 Precision Annex A (Normative) Electronic port fuel injector (PFI) test apparatus and related operation methods Annex B (Normative) Base gasoline