Codeofchina.com is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative.
The product indices in Table 1 of this Standard are all compulsory and other content is recommendatory.
This standard is not equivalent to the corresponding Japanese Industrial Standard JIS K1475: 2006 Poly Aluminium Chloride for Water Supply(Japanese version) and American Water Works Association Standard ANSI/AWWA B 408: 2003 Liquid Poly Aluminium Chloride (English Version).
Compared with JIS K 1475: 2006 and ANSI/AWWA B 408: 2003, the main differences are as follows:
- liquid poly aluminium chloride and solid poly aluminium chloride are included in this Standard.
- the technology index of basicity is increased according to the technological advance of poly aluminium chloride, and the production process and material source of poly aluminium chloride industry in China.
- the inspection method related to the heavy metal indices is changed.
- “the determination of ammoniacal nitrogen” is deleted.
This Standard replaces GB 15982-2003 Water Treatment Chemical – Poly Aluminium Chloride. Compared with GB 15890-2003, the main differences are as follows:
- This Standard name was changed into Poly Aluminium Chloride for Treatment of Drinking Water
- The technical index in Table 1 has been changed.
- The inspection method of aluminum oxide with CuSO4 standard volumetric solution is added.
- The determination method of some technical indices is modified.
-"The determination of ammonia nitrogen" is deleted.
Appendix A is informative.
This standard was proposed by China Petroleum and Chemical Industry Association.
This standard is under the jurisdiction of Subcommittee on Water Treatment Agent of the National Technical Committee on Chemical of Standardization Administration of China (SAC/TC 63/SC5).
Drafting organizations: Shenzhen Zhognrun Water Industry Technology Development Co.,Ltd., Tongji University, Taichang Xinxing Light Industry Auxiliary Factory, Shenzhen Qingyuan Water Purifier Co., Ltd, Shandong Purifiers Chemical Co., Ltd, Kemira Water Treatment Technology, Dongguan Huaqing Water Purification Materials Co., Ltd, Jiaozuo Aierfuke Chemical Industry Co., Ltd., Henan Huaquan Water Supply Material Head Factory, Henan New Century Purification material Co.Ltd.
Participating drafting organization of this standard: Tianjin Chemical Research and Design Institute of CNOOC, Wuxi Bisheng Water Treatment Agent Co.Ltd, Wuhan Zhongquin Fine Chemicals Co., Ltd., Gongyi Zhitian Water Purifying Materials Co., Ltd, Gongyi Yuqing Water Purigying Materials Co., Ltd., Gongyi Fuyyuan Water Purification Materials Co., Ltd, Chongqing University and Ningbo Huaguang Water Purifying Agent Industrial Corporation.
Chief drafting staff of this standard: Li Runsheng, Li Fengting, Tao Futang, Zhang Minquan, Jia Jiushun, Zhou Peng, Wang Longqing, Xu Zhiyuan, Yuan Mengbin and Tie Guibo.
The previous editions of the standards replaced by this standard are as:
- GB 15892—1995 and GB 15892—2003.
Poly Aluminium Chloride for Treatment of Drinking Water
生活飲用水用聚氯化鋁
1 Scope
This Standard specifies the technical requirements, test methods, test rules, packing, marking, transportation and storage of poly aluminium chloride for treatment of drinking water.
This Standard is applicable to poly aluminium chloride for treatment of drinking water. This product is mainly used in treatment of drinking water. Industrial synthetic hydrochloric acid shall be adopted for the raw material hydrochloric acid to produce poly aluminium chloride; the industrial alumina-hydroxide, kaolin, boehmite, gibbsite and calcium aluminate for water treatment agent shall be adopted for aluminiferous raw materials.
Rational formula Aln(OH)mCl(3n-m) 0
Contents
Foreword I
1 Scope
2 Normative References
3 Product Classification
4 Requirements
5 Test Methods
6 Test Rules
7 Marking, Packing, Transportation and Storage
Appendix A (Informative) Judgment of Coagulation Performance
生活飲用水用聚氯化鋁
1 范圍
本標準規定了生活飲用水用聚氯化鋁的要求、試驗方法、檢驗規則、包裝、標志、運輸和貯存。
本標準適用于生活飲用水用聚氯化鋁。該產品主要用于生活飲用水的凈化。生產聚氯化鋁的原料鹽酸,應采用工業合成鹽酸;含鋁原料,應采用工業氫氧化鋁、高嶺土、一水軟鋁石、三水鋁石和水處理劑用鋁酸鈣。
示性式:Aln(OH)mCl(3n-m) 0<m<3n
2 規范性引用文件
下列文件中的條款通過本標準的引用而成為本標準的條款。凡是注日期的引用文件,其隨后所有的修改單(不包括勘誤的內容)或修訂版均不適用于本標準,然而,鼓勵根據本標準達成協議的各方研究是否可使用這些文件的最新版本。凡是不注日期的引用文件,其最新版本適用于本標準。
GB/T 191 包裝儲運圖示標志
GB/T 601 化學試劑 標準滴定溶液的制備
GB/T 602 化學試劑 雜質測定用標準溶液的制備(GB/T 602—2002,ISO 6353-1:1982,NEQ)
GB/T 603 化學試劑 試驗方法中所用制劑及制品的制備(GB/T 603—2002,ISO 6353-1:1982,NEQ)
GB/T 610 化學試劑 砷測定通用方法(GB/T 610—2008,ISO 6353-1:1982,NEQ)
GB/T 6678 化工產品采樣總則
GB/T 6682 分析實驗室用水規格和試驗方法(GB/T 6682—2008,ISO 3696:1987,MOD)
GB/T 8946 塑料編織袋
3 產品分類
聚氯化鋁按型態分為液體和固體兩類。
4 要求
4.1 外觀
液體:無色至黃褐色液體。
固體:白色至黃褐色顆粒或粉末。
4.2 生活飲用水用聚氯化鋁指標應符合表1要求。
表 1
指標名稱 指 標
液體 固體
氧化鋁(Al2O3)的質量分?jǐn)?shù)/% ≥ 10.0 29.0
鹽基度/% 40.0~90.0
密度(20℃)/(g/cm3) ≥ 1.12 —
不溶物的質量分?jǐn)?shù)/% ≤ 0.2 0.6
pH值(10g/L水溶液) 3.5~5.0
砷(As)的質量分?jǐn)?shù)/% ≤ 0.0002
鉛(Pb)的質量分?jǐn)?shù)/% ≤ 0.001
鎘(Cd)的質量分?jǐn)?shù)/% ≤ 0.0002
汞(Hg)的質量分?jǐn)?shù)/% ≤ 0.00001
六價鉻(Cr+6)的質量分?jǐn)?shù)/% ≤ 0.0005
注:表中液體產品所列As、Pb、Cd、Hg、Cr+6、不溶物指標均按Al2O310%計算,Al2O3含量≥10%時,應按實際含量折算成Al2O310%產品比例計算各項雜質指標。
5 試驗方法
本標準所用試劑,除非另有規定,應使用分析純?cè)噭┖头螱B/T 6682中三級水的規定。
試驗中所需標準滴定溶液、雜質標準溶液、制劑及制品,在沒有注明其他要求時,均按GB/T 601、GB/T 602、GB/T 603的規定制備。
安全提示:本標準使用的強酸、強堿具有腐蝕性,使用時應注意。濺到身上時,用大量水沖洗。
5.1 氧化鋁(Al2O3)含量的測定(仲裁法)
5.1.1 氯化鋅標準溶液滴定法
5.1.1.1 方法提要
用硝酸將試樣解聚,在pH=3時加過量的乙二胺四乙酸二鈉溶液使EDTA與鋁離子絡合,然后用氯化鋅標準滴定溶液回滴過量EDTA溶液。
5.1.1.2 試劑和材料
5.1.1.2.1 硝酸溶液:1+12。
5.1.1.2.2 氨水溶液:1+1。
5.1.1.2.3 乙二胺四乙酸二鈉(EDTA)溶液:c(EDTA)約為0.05mol/L。
5.1.1.2.4 乙酸-乙酸鈉緩沖溶液(pH=5.5):稱取乙酸鈉(三水)272g溶于水中,加冰乙酸19mL,稀釋至1000mL。
5.1.1.2.5 氧化鋁標準溶液:1mL含0.001g Al2O3。
稱取0.5293g高純鋁(≥99.99%),精確至0.2mg,置于200mL聚乙烯杯中,加水20mL,加氫氧化鈉約3g,使其全部溶解透明(必要時在水浴上加熱),用鹽酸溶液(1+1)調節至酸性后再加10mL,使其透明,冷卻,移入1000mL容量瓶,稀至刻度,搖勻。
5.1.1.2.6 百里酚藍溶液:1g/L乙醇溶液。
5.1.1.2.7 二甲酚橙指示液:5g/L。
5.1.1.2.8 氯化鋅標準滴定溶液:c(ZnCl2)約0.025mol/L。
5.1.1.2.8.1 配制
稱取3.5g氯化鋅(ZnCl2),溶于鹽酸溶液[0.05%(體積分?jǐn)?shù))]中,稀釋至1L,搖勻。
5.1.1.2.8.2 標定
移取20.00mL EDTA溶液,置于250mL錐形瓶中,以下按5.1.1.3步驟進行操作,讀出氯化鋅標準滴定溶液的消耗量V0,mL。
移取20.00mL EDTA溶液和40mL氧化鋁標準溶液,置于250mL錐形瓶中,以下按5.1.1.3步
驟進行操作,讀出氯化鋅標準滴定溶液的消耗量V,mL。
5.1.1.2.8.3 結果計算
氯化鋅標準滴定溶液濃度c(ZnCl2),數值以摩爾每升(mol/L)表示,按式(1)計算:
c(ZnCl2)= ………………………………(1)
式中:
V1——氧化鋁標準溶液的體積的數值,單位為毫升(mL);
c1——氧化鋁標準溶液的濃度的數值,單位為克每毫升(g/mL);
M——氧化鋁的摩爾質量的數值,單位為克每摩爾(g/mol)(M=101.96);
V0——空白消耗氯化鋅標準滴定溶液的體積的數值,單位為毫升(mL);
V——返滴定時消耗氯化鋅標準滴定溶液的體積的數值,單位為毫升(mL)。
5.1.1.3 分析步驟
稱取約8g液體試樣或2.5g固體試樣,精確至0.2mg。用不含二氧化碳的水溶解,移入250mL容量瓶中,稀釋至刻度,搖勻。若稀釋液渾濁,用中速濾紙干過濾,此為試液A。
用移液管移取10mL試液A,置于250mL錐形瓶中,加10mL硝酸溶液,煮沸1min,冷卻至室溫后加20.00mL乙二胺四乙酸二鈉溶液,加百里酚藍溶液3~4滴,用氨水溶液中和至試液從紅色到黃色,煮沸2min。冷卻后加入10mL乙酸-乙酸鈉緩沖溶液和2滴二甲酚橙指示液,加水50mL,用氯化鋅標準滴定溶液滴定至溶液由淡黃色變?yōu)槲⒓t色即為終點,同時做空白試驗。
5.1.1.4 結果計算
氧化鋁(Al2O3)含量以質量分?jǐn)?shù) 計,數值以%表示,按式(2)計算:
………………………………(2)
式中:
V0——空白試驗消耗氯化鋅標準滴定溶液的體積的數值,單位為毫升(mL);
V——試樣消耗氯化鋅標準滴定溶液的體積的數值,單位為毫升(mL);
c——氯化鋅標準滴定溶液的實際濃度的準確數值,單位為摩爾每升(mol/L);
m——試料的質量的數值,單位為克(g);
M——氧化鋁的摩爾質量的數值,單位為克每摩爾(g/mol)(M=101.96)。
5.1.1.5 允許差
取平行測定結果的算術平均值為測定結果,平行測定結果的絕對差值:液體產品不大于0.1%;固體產品不大0.2%。
5.1.2 硫酸銅標準溶液滴定法
5.1.2.1 方法提要
在pH4.3時使EDTA與鋁離子絡合,以PAN為指示劑,用硫酸銅標準滴定溶液回滴過量EDTA溶液。
5.1.2.2 試劑和材料
5.1.2.2.1 鹽酸溶液:1+1。
5.1.2.2.2 氨水溶液:1+1。
5.1.2.2.3 緩沖溶液(pH約4.3):將42.3g無水乙酸鈉溶于水中,加80mL冰乙酸,用水稀釋至1L,搖勻。
5.1.2.2.4 乙二胺四乙酸二鈉(EDTA)溶液:c(EDTA)約0.05mol/L。
5.1.2.2.5 氧化鋁標準溶液:1mL含0.001gAl2O3。
同5.1.1.2.5。
5.1.2.2.6 1-(2-吡啶偶氮)-2-萘酚(PAN)指示溶液:將0.3gPAN溶于100mL 95%乙醇中。
5.1.2.2.7 硫酸銅標準滴定溶液:c(CuSO4)約0.025mol/L。
5.1.2.2.7.1 配制
稱取6.3g硫酸銅(CuSO4·5H2O)溶于水,加2滴硫酸溶液(1+1),用水稀釋至1L,搖勻。
5.1.2.2.7.2 標定
移取20.00mL EDTA溶液,置于250mL錐形瓶中,以下按5.1.2.3步驟進行操作,讀出硫酸銅標準滴定溶液的消耗量V0,mL。
移取20.00mL EDTA溶液和20mL氧化鋁標準溶液,置于250mL錐形瓶中,以下按5.1.2.3步
驟進行操作,讀出硫酸銅標準滴定溶液的消耗量V,mL。
5.1.2.2.7.3 結果計算
硫酸銅標準滴定溶液濃度c(CuSO4),數值以摩爾每升(mol/L)表示,按式(3)計算:
c(CuSO4)= ………………………………(3)
式中:
V1——氧化鋁標準溶液的體積的數值,單位為毫升(mL);
c1——氧化鋁標準溶液的濃度的數值,單位為克每毫升(g/mL);
M——氧化鋁的摩爾質量的數值,單位為克每摩爾(g/mol)(M=101.96);
V0——空白消耗硫酸銅標準滴定溶液的體積的數值,單位為毫升(mL);
V——返滴定時消耗硫酸銅標準滴定溶液的體積的數值,單位為毫升(mL)。
5.1.2.3 分析步驟
用移液管移取10mL試液A,置于250mL稚形瓶中,加鹽酸溶液(1+1)2mL,煮沸1min,加20.00mL EDTA溶液,加水至約100mL,加熱至約70℃~80℃,用氨水溶液(1+1)調節pH值至3.5~4.0(用0.5~5精密pH試紙檢查),加15.00mL pH4.3緩沖溶液,煮沸2min,加4~5滴PAN指示劑,稍冷(約95℃)以硫酸銅標準滴定溶液滴定至藍紫色。同時做空白試驗。
5.1.2.4 結果計算
氧化鋁(Al2O3)含量以質量分?jǐn)?shù)w2,數值以%表示,按式(4)計算:
……………………………………(4)
式中:
V0——空白消耗硫酸銅標準滴定溶液的體積的數值,單位為毫升(mL);
V——試樣消耗硫酸銅標準滴定溶液的體積的數值,單位為毫升(mL);
c——硫酸銅標準滴定溶液濃度的準確數值,單位為摩爾每升(mol/L);
m——試料的質量的數值,單位為克(g);
M——氧化鋁的摩爾質量的數值,單位為克每摩爾(g/moL),(M=101.96)。
5.1.2.5 允許差
取平行測定結果的算術平均值為測定結果,平行測定結果的絕對差值:液體產品不大于0.1%;固體產品不大于0.2%。
5.2 鹽基度的測定
5.2.1 方法提要
在試樣中加入定量鹽酸溶液,以氟化鉀掩蔽鋁離子,以氫氧化鈉標準滴定溶液滴定。
5.2.2 試劑和材料
5.2.2.1 鹽酸標準溶液:c(HCl)約0.5mol/L。
5.2.2.2 氫氧化鈉標準滴定溶液:c(NaOH)約0.5mol/L。
5.2.2.3 酚酞指示液:10g/L乙醇溶液。
5.2.2.4 氟化鉀溶液:500g/L。
稱取500g氟化鉀,以200mL不含二氧化碳的蒸餾水溶解后,稀釋至1000mL。加入2滴酚酞指示液并用氫氧化鈉溶液或鹽酸溶液調節溶液呈微紅色,濾去不溶物后貯于塑料瓶中。