標準編號:	FZ/T 62011.3-2016
中文名稱:	布藝類產品 第3部分：家具用紡織品
英文名稱:	Indoor ornamental textiles—Part 3: Slipcover
中標分類:	W59    其他紡織制品
行業分類:	FZ    紡織行業標準
ICS分類:	97.160 97.160    家用織物、亞麻織物 97.160
發布機構:	中華人民共和國工業和信息化部
發布日期:	2016-10-22
實施日期:	2017-4-1
標準狀態:	valid
替代舊標準:	FZ/T 62011.3-2008 布藝類產品 第3部分:家具用紡織品
翻譯語言:	英文
文件格式:	PDF
中文字符數:	10000 字
翻譯價格(元):	300.0
交付時間:	付款后 1 個工作日

Codeofchina.com is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative. FZ/T 62011 Indoor Ornamental Textiles is divided into four parts: ——Part 1: Curtain; ——Part 2: Dinning Table Textiles; ——Part 3: Upholstery; ——Part 4: Interior Decoratives. This part is the third part of FZ/T 62011. This part is developed in accordance with the rules given in GB/T 1.1-2009. This part replaces FZ/T 62011.3-2008 Indoor Ornamental Textiles - Part 3: Upholstery. The following main changes have been made with respect to FZ/T 62011.3-2008 (the previous edition): ——The assessment indexes for first-grade products on breaking strength are improved (see 4.2; 4.2 in Edition 2008); ——The assessment requirements for first-grade products and qualified products on tearing strength are improved (see 4.2; 4.2 in Edition 2008); ——Assessment requirements on fuzzing and pilling and metal residues in inherent quality are added (see 4.2); ——Assessment requirements on deviation rate of dimension, skewness, bow and dyeing defect in appearance quality are added; ——Shape quality requirements in appearance quality are deleted (see 4.3; 4.3 in Edition 2008); ——Assessment requirements for embroidery quality in process quality are added (see 4.3); ——Assessment requirements for first-grade products and qualified products on color spot and stain are improved (see 4.3). This part was proposed by China National Textile and Apparel Council. This part is under the jurisdiction of National Technical Committee 302 on Household Textiles of Standardization Administration of China (SAC/TC 302). Previous edition of this standard is as follows: ——FZ/T 62011.3-2008. Indoor Ornamental Textiles – Part 3: Upholstery 1 Scope This part of FZ/T 62011 specifies the terms and definitions, requirements, sampling, test methods, inspection rules, and marking, packaging, transportation and storage of indoor ornamental textiles - upholstery. This part is applicable to upholstery mainly made of textile and woven. 2 Normative References The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 250 Textiles - Tests for Color Fastness - Grey Scale for Assessing Change in Color GB/T 251 Textiles - Tests for Color Fastness - Grey Scale for Assessing Staining GB/T 14801 Test Method for Skewness and Bow in Woven and Knitted Fabrics GB/T 3917.2 Textiles--Tear Properties of Fabrics - Part 2:Determination of tear force of tongue shaped test specimens GB/T 3920 Textiles - Tests for Color Fastness - Color Fastness to Rubbing GB/T 3921-2008 Textiles - Tests for Color Fastness - Color Fastness to Soaping GB/T 3923.1 Textiles - Tensile Properties of Fabrics - Part 1: Determination of Breaking Force and Elongation at Breaking Force - Strip Method GB/T 4802.2 Textiles - Determination of Fabric Propensity to Surface Fuzzing and to Pilling - Part 2: Modified Martindale Method GB 5296.4 Instructions for Use of Products of Consumer Interest - Part 4: Textiles and Apparel GB/T 5711 Textiles - Tests for Colour Fastness - Colour Fastness to Dry Cleaning GB/T 8170 Rules of Rounding Off for Numerical Values & Expression and Judgment of Limiting Values GB/T 8427 Rules of Rounding Off for Numerical Values & Expression and Judgment of Limiting Values GB/T 8628 Textiles - Preparation, Marking and Measuring of Fabric Specimens and Garments in Tests for Determination of Dimensional Change GB/T 8629-2001 Textiles - Domestic Washing and Drying Procedures for Textile Testing GB/T 8630 Textile - Determination of Dimensional Change in Washing and Drying GB 18401 National General Safety Technical Code for Textile Products GB/T 13772.2 Textiles - Determination of the Slippage Resistance of Yarns at a Seam in Woven Fabrics - Part 2: Fixed Load Method GB/T 24121 Textile Products - Determination of the Remains of Broken Sewing Needle GB/T 29862 Textiles - Identification of Fiber Content FZ/T 80007.3 Dry Wash Resistance Test Method for Garments used Adhesive Interlining GSB 16-3223 Standard Sample Photos of Household Textiles Pilling 3 Terms and Definitions For the purposes of this document, the following terms and definitions apply. 3.1 indoor ornamental textiles textile products mainly made of textile material, used for indoors with indoor decoration and/or utility function and mainly divided into curtain, dinning table textiles, upholstery and interior decoratives 3.2 upholstery textile products mainly made of textile material, used for furniture and detachable furniture, e.g. fabric sofa, furniture coverage, slip cover etc. 4 Requirements 4.1 Quality of upholstery products includes inherent quality and appearance quality, while quality grade can be classified into high-grade products, first-grade products and qualified products. 4.2 Inherent quality includes breaking strength, tearing strength, yarn slippage, fuzzing and pilling, dimensional stability to washing, dimensional stability to dry cleaning, color fastness and fiber content, see Table 1 for the inherent quality requirements. Table 1 Inherent Quality Requirements S.N. Assessment item High-grade products First-grade products Qualified products 1 Breaking strength /N ≥ 250 220 2 Tearing strength /N ≥ 20 15 3 Yarn slippage/mm ≤ 4 6 7 4 Fuzzing and pilling a/Grade ≥ 3-4 3 5 Dimensional stability to washing b/% -2.5~+1.0 -3.0~+1.0 -4.0~+1.0 6 Dimensional stability to dry cleaning c/% -2.5~+1.0 -3.0~+1.0 7 Color fastness/Grade ≥ Soaping fastness b Discoloring 4 3-4 3 Staining 4 3-4 3 Dry cleaning fastness c Discoloring 4 3-4 3 Staining 4 3-4 3 Rubbing fastness Dry rubbing 4 3-4 3 Wet rubbing 3-4 3 2-3 Light fastness 5 4 3 8 Fiber content/% In accordance with the requirements of GB/T 29862 a Yarn slippage, fuzzing and pilling are applicable to fabric sofa, slipcover and chair cover products; b Dimensional stability to washing and color fastness to soaping are applicable to washable products; c Dimensional stability to dry cleaning and color fastness to dry cleaning are applicable to dry-cleaning products. Soaping fastness, dry cleaning fastness and color fastness to rubbing are not assessed for raw white and bleaching products. 4.3 The appearance quality of products includes color difference, appearance defects, process requirements and sewing quality, see Table 2 for the their requirements. Table 2 Appearance Quality Requirements Assessment item High-grade products First-grade products Qualified products Deviation rate of specification and dimension/% ±1.5 ±2.5 -2.5~+3.5 Skewness and bow/% ≤ 2.0 3.0 4.0 Color difference/Grade ≥ 4-5 4 3-4 Appearance defects Damage and pinhole Not allowed Not allowed Damage is not allowed and length of pinhole is less than 20cm Color spot and stain Not allowed For Grade 4 stain, 1 place is allowed each piece and length is not greater than 8.0cm For Grade 3-4 stain, 1 place is allowed each piece and length is not greater than 8.0cm Linear defect Not allowed One slight defect is allowed each piece and length is not greater than 8.0cm One obvious defect is allowed each piece and length is not greater than 8.0cm Strip and block defect Not allowed One slight defect is allowed each piece and length is not greater than 8.0cm One obvious defect is allowed each piece and length is not greater than 8.0cm Poor printing Not allowed Slight overlapping, staining, bleeding or skip printing, not affecting the appearance Not affecting overall appearance Process requirements Pattern quality Entire pattern not deviated Not affecting overall appearance Sewing quality Stitch quality No skipped stitch, float stitch, drop stitch, deviated stitch or off-thread No skipped stitch, float stitch, drop stitch, and off-thread; deviated stitch not exceeding 0.5cm/20cm Quilting quality Track is smooth and flat without winkles or insertion; back stitching is needed at the quilting starting and ending points; split stitch is straight without thread end and with regular stitches Sewing quality Stitches are even, straight and firm; crimping and abutted seam are flat, smooth, even and straight with consistent width and without fur exposure; unless otherwise required by the process, it shall be free from nap up/down; back stitching is needed at the sides and corners where the surface/lining sewing disalignment is less than 1cm; stitch density: flat seaming≥8 stiches/3cm; over seaming≥9 stiches/3cm; herringbone stitch≥8 stiches/3cm and package terrier needle≥23 stitches/3cm, raw corner is not allowed Embroidery quality Stitches are flat and smooth, embroidery surface is flat; the pattern variation is natural and embroidery contour is uniform; stitches are even, thin and properly fine; needle transmission is fluent, color mix is natural and is full of stereoscopic impression; the embroidery surface is clean without stain. The applique embroidery shall be smooth and flat and free from obvious missed embroidery, the sprayed embroidery shall be accurate and its transition shall be natural and free from overlapping and misplacement Note: see Annex A for description of appearance defects and degree. 4.4 Products shall meet the requirements of GB 18401. 4.5 Products shall be free from metal residues which are harmful to human body such as suture needle and broken needle. 4.6 Appropriate accessories like thread, button and zipper shall be selected and their quality shall meet the requirements of relevant standards.

Foreword i 1 Scope 2 Normative References 3 Terms and Definitions 4 Requirements 5 Sampling 6 Inspection Methods 7 Inspection Rules 8 Marking, Packaging, Transportation and Storage Annex A (Informative) Description of Appearance Defect and Degree

ICS 97.160 W 59 中華人民共和國紡織行業標準 FZ/T 62011.3—2016 代替FZ/T 62011.3—2008 布藝類產品 第3部分：家具用紡織品 Indoor ornamental textiles—Part 3：Upholstery 2016—10—22發布 2016—12—01實施 中華人民共和國工業和信息化部 發布 前言 FZ/T 62011《布藝類產品》分為四個部分： ——第1部分：帷幔； ——第2部分：餐用紡織品； ——第3部分：家具用紡織品； ——第4部分：室內裝飾物。 本部分為FZ/T 62011的第3部分。 本部分按照GB/T 1.1—2009給出的規則起草。 本部分代替FZ/T 62011.3—2008《布藝類產品 第3部分：家具用紡織品》。 本部分與FZ/T 62011.3—2008相比主要變化如下： ——提高了斷裂強力一等品的考核指標(見4.2，2008年版4.2)； ——提高了撕破強力一等品、合格品的考核要求(見4.2，2008年版4.2)； ——內在質量增加了起毛起球、金屬殘留物的考核要求(見4.2)； ——外觀質量增加了尺寸偏差率、緯斜、花斜、色花的考核要求； ——刪除了外觀質量中的造型質量要求(見4.3，2008年版4.3)； ——工藝質量增加了刺繡質量考核要求(見4.3)； ——提高了色污漬一等品和合格品的考核要求(見4.3)。 本部分由中國紡織工業聯合會提出。 本部分由全國家用紡織品標準化技術委員會(SAC/TC 302)歸口。 本部分起草單位：愉悅家紡有限公司、江蘇省紡織產品質量監督檢驗研究院。 本部分主要起草人：張國清、唐祖根、王玉平。 本部分所代替標準的歷次版本發布情況為： ——FZ/T 62011.3—2008。 布藝類產品 第3部分：家具用紡織品 1 范圍 FZ/T 62011的本部分規定了布藝類產品——家具用紡織品的術語和定義、要求、抽樣、試驗方法、檢驗規則、標志、包裝、運輸和貯存。 本部分適用于以紡織機織為主制成的家具用紡織品。 2規范性引用文件 下列文件對于本文件的應用是必不可少的。凡是注日期的引用文件，僅注日期的版本適用于本文件。凡是不注日期的引用文件，其最新版本(包括所有的修改單)適用于本文件。 GB/T 250 紡織品 色牢度試驗 評定變色用灰色樣卡 GB/T 251 紡織品 色牢度試驗 評定沾色用灰色樣卡 GB/T 14801 機織物與針織物緯斜和弓緯試驗方法 GB/T 3917.2紡織品 織物撕破性能 第2部分：褲形試樣單縫撕破強力的測定 GB/T 3920紡織品 色牢度試驗 耐摩擦色牢度 GB/T 3921—2008 紡織品 色牢度試驗 耐皂洗色牢度 GB/T 3923.1紡織品 織物拉伸性能 第1部分：斷裂強力和斷裂伸長率的測定(條樣法) GB/T 4802.2紡織品 織物起毛起球性能的測定 第2部分：改型馬丁代爾法 GB 5296.4消費品使用說明 第4部分：紡織品和服裝 GB/T 5711 紡織品 色牢度試驗 耐干洗色牢度 GB/T 8170數值修約規則與極限數值的表示和判定 GB/T 8427 紡織品 色牢度試驗 耐人造光色牢度：氙弧 GB/T 8628紡織品 測定尺寸變化的試驗中織物試樣和服裝的準備、標記和測量 GB/T 8629—2001紡織品 試驗用家庭洗滌和干燥程序 GB/T 8630紡織品 在洗滌和干燥時尺寸變化的測定 GB 18401 國家紡織產品基本安全技術規范 GB/T 13772.2紡織品 機織物接縫處紗線抗滑移的測定 第2部分：定負荷法 GB/T 24121紡織制品 斷針類殘留物的檢測方法 GB/T 29862紡織品 纖維含量的標識 FZ/T 80007.3使用粘合襯服裝耐干洗測試方法 GSB 16—3223家用紡織品 起球標準樣照 3術語和定義 下列術語和定義適用于本文件。 3.1 布藝類產品indoor ornamental textiles 主要部分由紡織原料制成，用于室內，具有裝飾和/或?qū)嵱霉δ艿募徔椫破?。主要分為帷幔、餐用紡織品、家具用紡織品、室?nèi)裝飾物。 3.2 家具用紡織品upholstery 主要以紡織品為原料制成的家具和可以脫卸的家具中的紡織制品，如布藝沙發、家具鋪蓋物、家具套等。 4 要求 4.1 家具用紡織品產品的質量包括內在質量和外觀質量。質量等級分為優等品、一等品和合格品。 4.2 內在質量包括斷裂強力、撕破強力、紗線滑移、起毛起球、水洗尺寸變化率、干洗尺寸變化率、色牢度、纖維含量，內在質量要求見表1。 表1 內在質量要求 序號 考核項目 優等品 一等品 合格品 1 斷裂強力/N ≥ 250 220 2 撕破強力/N ≥ 20 15 3 紗線滑移/mm ≤ 4 6 7 4 起毛起球a/級 ≥ 3—4 3 5 水洗尺寸變化率b/％ -2.5～+1.0 -3.0～+1.0 -4.0～+1.0 6 干洗尺寸變化率c/％ -2.5～+1.0 -3.0～+1.0 7 色牢度/級 ≥ 耐皂洗b 變色 4 3—4 3 沾色 4 3—4 3 耐干洗c 變色 4 3—4 3 沾色 4 3—4 3 耐摩擦 干摩 4 3—4 3 濕摩 3—4 3 2—3 耐光 5 4 3 8 纖維含量/％ 按GB/T 29862規定執行 a紗線滑移、起毛起球適用于布藝沙發、沙發套和椅套類產品； b水洗尺寸變化率、耐皂洗色牢度適用于可水洗產品； c干洗尺寸變化率、耐干洗色牢度適用于可干洗的產品。 本白和漂白產品不考核耐皂洗、耐干洗、耐摩擦色牢度。 4.3產品的外觀質量包括色差、外觀疵點、工藝要求、縫制質量，要求見表2。 表2外觀質量要求 考核項目 優等品 一等品 合格品 規格尺寸偏差率/％ ±1.5 ±2.5 -2.5～+3.5 緯斜、花斜/％ ≤ 2.0 3.0 4.0 色差/級 ≥ 4—5 4 3—4 表2(續) 考核項目 優等品 一等品 合格品 外觀疵點 破損、針眼 不允許 不允許 破損不允許，針眼長度小于20 cm 色、污漬 不允許 沾污4級，允許1處/件， 長度不超過8.0 cm 沾污3-4級，允許1處/件，長度不超過8.0 cm 線狀疵點 不允許 輕微允許1處/件， 長度不超過8.0 cm 明顯允許1處/件，長度不超過8.0 cm 條塊狀疵點 不允許 輕微允許1處/件， 長度不超過8.0 cm 明顯允許1處/件，長度不超過8.0 cm 印花不良 不允許 輕微搭、沾、滲色， 漏印，不影響外觀 不影響整體外觀 工藝要求 圖案質量 圖案整體位正不偏 不影響整體外觀 縫制質量 縫跡質量 無跳、浮、漏、偏針和脫線 無跳、浮、漏針，脫線；偏針不超過0.5 cm/20 cm 絎縫質量 軌跡流暢、平服，無折皺夾布；絎縫起止處打回針，接針套正，無線頭；針跡整齊均勻 縫紉質量 軌跡勻、直、牢固，卷邊拼縫平服齊直，寬狹一致，不露毛，非工藝要求不允許有順逆毛現象；面/里料縫制錯位小于1 cm邊口處應打回針；針跡密度：平縫≥8針/3cm；包縫≥9針/3 cm；三角針≥8針/3 cm；包梗針≥23針/3 cm，不允許有散角 刺繡質量 針碼平服，繡面平整；圖案花型變化自然，繡邊輪廓齊整；針碼均勻細薄、細密適當；行針流暢，摻色自然，富有立體感；繡面潔凈無沾污。貼繡平服，無明顯漏繡，噴繡色彩準確，過渡自然，不重疊、不錯位 注：外觀疵點及程度說明參見附錄A。 4.4產品應符合GB 18401的要求。 4.5產品應無縫針、斷針等對人體有害的金屬殘留物。 4.6選用適合的縫線、紐扣、拉鏈等附件，且質量符合相關標準要求。 5抽樣 5.1 內在質量檢驗抽樣方案見表3。 表3 內在質量檢驗抽樣方案 批量范圍N 樣本大小n 合格判定數Ac 不合格判定數Re 1～500 1 0 1 501～35 000 2 0 1 >35 000 3 0 1 5.2外觀質量檢驗抽樣方案見表4。 表4外觀質量檢驗抽樣方案 批量范圍N 樣本大小n 合格判定數Ac 不合格判定數Re 1～500 20 1 2 501～1 200 32 3 4 1 201～3 200 50 5 6 >3 200 80 10 11 5.3檢驗樣本應從檢驗批中隨機抽取，外包裝應完整。 5.4實施抽樣時，當樣本大小n大于批量N時，實施全檢，合格判定數Ac為0。 5.5抽樣方案另有規定和合同協議的，按有關規定和合同協議執行。 6試驗方法 6.1 內在質量檢測 6.1.1 斷裂強力檢測按GB/T 3923.1執行。 6.1.2 撕破強力檢測按GB/T 3917.2執行。 6.1.3 紗線滑移檢測按GB/T 13772.2執行。 6.1.4起毛起球檢測按GB/T 4802.2執行，以試樣織物為磨料，摩擦次數2 000次。評級按GSB 16-3223評級樣照進行。 6.1.5 水洗尺寸變化率檢測按GB/T 8628，GB/T 8629—2001和GB/T 8630執行，選用5A程序，干燥方法F。 6.1.6 干洗尺寸變化率檢測按FZ/T 80007.3執行。 6.1.7耐皂洗色牢度檢測按GB/T 3921—2008執行，試驗采用A(1)。 6.1.8 耐干洗色牢度檢測按GB/T 5711執行。 6.1.9 耐摩擦色牢度檢測按GB/T 3920執行。 6.1.10耐光色牢度檢測按GB/T 8427執行，試驗采用方法3。 6.1.11 數值修約按GB/T 8170執行。 6.2外觀質量檢驗 6.2.1工具：鋼尺，以毫米為刻度，其長度大于所測量方法的最大尺寸。 6.2.2外觀質量檢驗以產品的正面為主，檢驗時產品表面照度不低于600 lx，檢驗人員眼部距產品約1 m左右，檢驗人員用鋼尺測量，以目光、手感進行檢驗。 6.2.3規格尺寸偏差率的測定：將產品平攤在檢驗臺上，用手輕輕理平，使產品呈自然伸縮狀態，用鋼尺在整個產品長、寬方向的1/4和3/4處測量，取最大長度和最大寬度后平均，精確到1 mm，按式(1)進行計算，計算結果按GB/T 8170修約至1位小數。 …………………………(1) 式中： P——規格尺寸偏差率，％； L0——產品規格尺寸明示值，單位為毫米(mm)； L1——產品規格尺寸實測平均值，單位為毫米(mm)。 6.2.4色差檢測用GB/T 250評定變色用灰色樣卡進行評定。 6.2.5色、污漬檢測用GB/T 251評定沾色用灰色樣卡進行評定。 6.2.6 緯斜檢測按GB/T 14801執行。 6.2.7工藝質量的檢測，由檢驗人員使用鋼尺，結合目光、手感進行檢驗。 6.3縫針、斷針等金屬殘留物按GB/T 24121執行。 7檢驗規則 7.1單件產品內在質量、外觀質量分別按表1、表2中最低一項評等，綜合質量按內在質量和外觀質量中的最低等評定。 7.2批判定時內在質量按抽樣方案表3執行，外觀質量批判定按抽樣方案表4執行。不合格數小于Re，則判檢驗批合格；不合格數大于或等于Re，則判檢驗批不合格。 7.3綜合質量批評定按內在質量抽樣檢查和外觀質量抽樣檢查中最低等評定。 8標志、包裝、運輸和貯存 8.1產品使用說明應符合GB 5296.4的要求。產品應標明規格尺寸和單位，特殊產品按設計標注，異形產品不標注尺寸。 8.2產品應分類包裝，包裝大小根據具體產品而定。包裝材料應選擇適當，應保證不散落、不破損、不沾污、不受潮。 8.3產品運輸應防潮、防火、防污染。 8.4產品應放在陰涼、通風、干燥、清潔庫房內，并防蛀、防霉。 附 錄 A (資料性附錄) 外觀疵點及程度說明 A.1線狀疵點：沿經向或緯向延伸的，寬度不超過0.2 cm的所有各類疵點。 A.2條塊狀疵點：沿經向或緯向延伸的，寬度超過0.2 cm的疵點，不包括色、污漬。 A.3破損：相鄰的紗、線斷2根及以上的破洞，破邊，0.3 cm及以上的跳花。 A.4疵點輕微、明顯程度見表A.1。 表A.1 外觀疵點及程度說明 印染疵 對比GB/T 250評定變色用灰色樣卡，3—4級及以上為輕微，3—4級以下為明顯 紗、織疵 線狀 輕微 粗度不大于紗支3倍的粗經，線狀錯經，稀1根～2根紗的筘路，粗度不大于紗支3倍的粗緯，雙緯，線狀百腳，竹節紗等 明顯 粗度大于紗支3倍的粗經，鋸齒狀錯經，斷經，跳紗，稀2根紗以上的筘路，粗度大于紗支3倍的粗緯、竹節紗，脫緯，鋸齒狀百腳，一梭3根的多紗，色、油、污紗等 條塊狀 輕微 雜物織入，條干不勻，經縮波紋，疊起來看不易發現的稀密路，折痕不起毛 明顯 并列跳紗，明顯影響外觀的雜物織人、條干不勻，疊起來看容易發現的稀密路，折痕起毛，經縮浪紋，寬0.2 cm以上的筘路、針路等